[ Pobierz całość w formacie PDF ]
. the column on the locating pin, the two steering column mounting bolts and tightenTighten the steering wheel mounting bolt to torque.them to torque.Connect:Position the linking fork and tighten the two mounting the horn connector,bolts to torque. the driver's front airbag module connector.Connect the ignition switch connectors.WARNING:Replace and clip in place the wiring harnessTake care to remember to remove any foreignattachments.bodies (bolts, clips etc.) when refitting the airbagmodules.On the airbag elements, it is essential toReplace and connect:clip the connectors to the bottom and position the the transponder ring,safety latches. the rotary switch.Refit:WARNING: the half cowlings,Before unlocking the pyrotechnic systems computer, the instrument panel visor,carry out a test using the diagnostic tool.If the steering wheel.everything is correct, unlock the computer, if not,refer to the fault finding section.WARNING:Failure to observe these instructions may cause afault in the normal operation of the pyrotechnicsystems, i.e.they may be incorrectly triggered.Refit the driver's front airbag module.Connect the battery.Check, and adjust if necessary, the alignment of thefront wheels.WARNING:The steering wheel splines are made so that thewheel can be fitted in one position only.The steeringwheel should be inserted freely into the splines.36-9 STEERING ASSEMBLY36Intermediate shaftIntermediate shaftTIGHTENING TORQUES (in daNm)Linking fork bolt 2.1Universal joint nut 2.1REMOVAL the universal joint shaft and nut (B).Unclip the sealing gaiter on the engine compartmentRemove: side. the two linkage mounting bolts (A). the linking fork, Remove the intermediate shaft, pulling it from thepassenger compartment side.REFITTINGProceed as for the removal in reverse, taking care to fita new nut to the universal joint.Tighten the fork mounting bolts to torque.Check, and adjust if necessary, the alignment of thefront wheels.36-10 [ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl trzylatki.xlx.pl
. the column on the locating pin, the two steering column mounting bolts and tightenTighten the steering wheel mounting bolt to torque.them to torque.Connect:Position the linking fork and tighten the two mounting the horn connector,bolts to torque. the driver's front airbag module connector.Connect the ignition switch connectors.WARNING:Replace and clip in place the wiring harnessTake care to remember to remove any foreignattachments.bodies (bolts, clips etc.) when refitting the airbagmodules.On the airbag elements, it is essential toReplace and connect:clip the connectors to the bottom and position the the transponder ring,safety latches. the rotary switch.Refit:WARNING: the half cowlings,Before unlocking the pyrotechnic systems computer, the instrument panel visor,carry out a test using the diagnostic tool.If the steering wheel.everything is correct, unlock the computer, if not,refer to the fault finding section.WARNING:Failure to observe these instructions may cause afault in the normal operation of the pyrotechnicsystems, i.e.they may be incorrectly triggered.Refit the driver's front airbag module.Connect the battery.Check, and adjust if necessary, the alignment of thefront wheels.WARNING:The steering wheel splines are made so that thewheel can be fitted in one position only.The steeringwheel should be inserted freely into the splines.36-9 STEERING ASSEMBLY36Intermediate shaftIntermediate shaftTIGHTENING TORQUES (in daNm)Linking fork bolt 2.1Universal joint nut 2.1REMOVAL the universal joint shaft and nut (B).Unclip the sealing gaiter on the engine compartmentRemove: side. the two linkage mounting bolts (A). the linking fork, Remove the intermediate shaft, pulling it from thepassenger compartment side.REFITTINGProceed as for the removal in reverse, taking care to fita new nut to the universal joint.Tighten the fork mounting bolts to torque.Check, and adjust if necessary, the alignment of thefront wheels.36-10 [ Pobierz całość w formacie PDF ]